Skip to main content
Search Interpretations

Interpretation ID: aiam5148

Mr. Steven C. Friedman Director of New Product Development Saddleman, Inc. P.O. Box 3656 80 West 900 South Logan, UT 84323-3656; Mr. Steven C. Friedman Director of New Product Development Saddleman
Inc. P.O. Box 3656 80 West 900 South Logan
UT 84323-3656;

"Dear Mr. Friedman: This responds to your January 19, 1993, lette asking for information on any Federal motor vehicle safety standards applicable to retrofit air bags. Your letter states that these devices are intended for vehicles which do not have factory-installed air bags. I am pleased to have this opportunity to explain our laws and regulations to you. The National Traffic and Motor Vehicle Safety Act (the Safety Act, 15 U.S.C. 1381 et seq.) authorizes this agency to issue Federal motor vehicle safety standards applicable to new motor vehicles and new items of motor vehicle equipment. NHTSA has exercised this authority to establish Standard No. 208, Occupant Crash Protection (49 CFR 571.208). Standard No. 208 requires, among other things, that passenger cars provide automatic crash protection. Light trucks will also be required to provide automatic crash protection beginning with the 1995 model year. Vehicles equipped with automatic crash protection protect their occupants by means that require no action by vehicle occupants. Compliance with the automatic crash protection requirements of Standard No. 208 is determined in a dynamic crash test. That is, a vehicle must comply with specified injury criteria, as measured on a test dummy, when tested by this agency in a 30 mph barrier crash test. At this time, manufacturers are not required to use a specific method of automatic crash protection to meet the requirements of Standard No. 208. Instead, each automobile manufacturer is allowed to select the particular method for the automatic crash protection installed in its vehicles. The two types of automatic crash protection currently offered on new passenger cars are automatic safety belts (which help to assure belt use) and air bags (which supplement safety belts and offer some protection even when safety belts are not used). Please note that the automatic crash protection requirement applies to the performance of the vehicle as a whole, instead of setting requirements for the air bag as an individual item of equipment. This approach permits vehicle manufacturers to 'tune' the performance of the air bag to the crash pulse and other specific attributes of each of their vehicle models. However, this approach also means that the Federal standards do not specify specific performance attributes for air bags such as inflated dimensions, actuation time, and the like. While most of Standard No. 208's requirements are expressed in terms of the performance of the vehicle as a whole and apply only to new vehicles and not to aftermarket equipment, there is one exception to this. Pressure vessels and explosive devices for use in air bag systems must comply with section S9 of Standard No. 208 whether they are part of a new motor vehicle or are aftermarket equipment. Therefore, the manufacturer of these items must certify that they comply with the requirements of S9 of Standard No. 208. Another Federal requirement that would affect a retrofit air bag is the 'render inoperative' prohibition in section 108(a)(2)(A) of the Safety Act (15 U.S.C. 1397(a)(2)(A)). That section provides that: No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative, in whole or in part, any device or element of design installed on or in a motor vehicle ... in compliance with an applicable Federal motor vehicle safety standard. The 'render inoperative' provision would prohibit a commercial business from installing an aftermarket air bag in a manner that would negatively affect the vehicle's compliance with Standard No. 208 or any other safety standard. You should also note that a replacement or retrofit air bag would be considered 'motor vehicle equipment' within the meaning of the Safety Act. Therefore, if the air bag contained a defect (either in manufacture, design, or performance) that relates to motor vehicle safety, the manufacturer would be required to conduct a recall campaign to notify owners and to remedy the defect free of charge. Please note that recently a manufacturer of an aftermarket air bag that did not provide any crash protection benefits to vehicle occupants recalled its air bags following a NHTSA investigation. In addition, NHTSA provided information to the Federal Trade Commission concerning the claims made by the manufacturer in its advertising. We suggest you carefully review the test data on the devices you are considering importing to assure yourself that the air bag would afford adequate protection to vehicle occupants in crashes and that the claims made in the company's advertising are true. I also note that, based on the product information you provided with your letter, NHTSA technical staff raised possible concerns about the air bag you are considering importing. The design differs from other air bags in two significant ways. First, while the crash sensor for air bag systems is normally located in the vehicle structure, yours is not. Second, while air bags generally are released toward the driver's chest from the steering wheel, your air bag would be released from above toward the driver's face and chest. For driver crash protection, the crash sensor of an air bag system must initiate deployment of the air bag early enough in a crash to position the inflated air bag between the driver and the steering wheel in time to cushion the impact. At the same time, it must not be so sensitive that it deploys the air bag in non-crash situations. Given the ways in which the crash sensor of your system differs from other air bag systems, our technical staff questions whether it is possible for it to initiate deployment early enough in a crash to provide occupant protection yet not be so sensitive that it deploys the air bag in non-crash situations. In addition, while the inadvertent deployment of any air bag system would raise safety concerns, the location of your air bag would increase those concerns, since it would appear to interfere with the driver's forward vision even after deflation. I have enclosed an information sheet that identifies relevant Federal statutes and NHTSA standards and regulations affecting motor vehicle and motor vehicle equipment manufacturers, and explains how to get copies of these materials. I hope you find this information helpful. If you have any other questions, please contact Mary Versailles of my staff at this address or by phone at (202) 366-2992. Sincerely, John Womack Acting Chief Counsel Enclosure";